7.3L Engine Specs / Torque Specs
Peak Torque: • 425 lb-ft @ 2, 000 rpm (intro torque rating, 1994 MY). First thing's first, I lay out my parts. Helms manual defines the front two bolts get 24 ft lbs and the rear three get 14 ft lbs. While you are there replace the turbo lines. 3L Power Stroke engines use "A" code injectors, which feature a 16.
- 7.3 oil cooler torque specs reviews
- 7.3 oil cooler torque specs problems
- Cummins oil cooler torque specs
7.3 Oil Cooler Torque Specs Reviews
I used an inch # when I do the little ones. Well, I'm not using this line anyway, lets cut this thing! I'll double check to make sure that it is not simply too loose, otherwise I'm throwing an FC cooler in there, it should be easy enough once I get the correct lines for that application. Reinstall the steering shaft. Connect the engine block heater electrical connector. 3L Powerstroke products, this replacement oil cooler is backed by our Mishimoto Lifetime Warranty for a lifetime of worry-free driving. I remove the AC belt, fan, and shroud. Anyone know the torque specs for oil cooler lines. NOTE: Snug capscrew numbers six and eight, then tighten in stages the sequence shown. You should be using aluminum washers. Lift Not Required (But It Sure Helps). The stock 1994-2003 7. In comparison to the prior mechanical injection system, the transition to HEUI promised improved performance, lower emissions, and better fuel economy stemming from increased fuel atomization and greater control over injection events.
7.3 Oil Cooler Torque Specs Problems
Width: 32" (approx). Front support bracket to engine mounting bolts. Air brake ABS module bracket assembly mounting nuts. 1st Generation Dodge Cummins 89-93. 3L IDI Diesel Oil Cooler Parts List. The molded in orings aren't very thick and don't look to be too forgiving! Click any thumbnail to view fullsize, detailed image. Transmissions torque converter. 6, 7 swap, Dual pumps, 467. 7.3 oil cooler torque specs reviews. What are the torque specs on the following: Injector retainer... 28 lbs. To better access the pair of 10mm bolts in the front oil cooler header, you can pull the lower radiator hose.
Cummins Oil Cooler Torque Specs
Transmission oil cooler hoses. So, I lay down in the pool of oil. • For reference, see diagram at left for location of various bolt lengths for the rear oil cooler header. • This oil cooler is not mixing oil and coolant, but has a developed a severe leak at both ends and is therefore losing oil rapidly. Ford E4TZ-6881-C. [3]. See fullsize image for detailed view. For the 2003 MY, the 7. 7.3 oil cooler torque specs problems. Parking brake cable clamp mounting bolts (manual transmission). 3L Power Stroke was offered alongside the new, smaller 6. Breaking Down the Oil Cooler. • Drain the engine coolant as much as possible. Air cleaner support bracket mounting nuts.
The instructions that came with them said "for the first use, torque them to XX ft-lbs, then the next time you tighten them torque it 10% higher, then the next time 10% higher than that. • Once you've removed the oil cooler from the vehicle, tip the cooler over a drain pan and drain as much oil out of it as possible. Bolts to make sure that the two larger components stay securely together. Oh well, I'll do that later. Once the first o-ring land is exposed, you can use a flathead screwdriver to gently pry it the rest of the way off.. The rear header bolts are varying lengths - label the bolts as they are removed, or refer to the diagram below for proper assignment of the bolts. For more detailed transmission information please see the transmission section on. Ford 7.3 Powerstroke 94-03 Replacement Oil Cooler - By Mishimoto. Check that nothing is wedged between the engine and trans and that the torque converter is in its proper place. Loosen up when the engine is running otherwise you could end up with a major issue on your hands.